How to Measure for Custom Curtains: Width & Length

UniCurt measuring guide

How to Measure for Custom Curtains: From Your Window to the Sizes You Order

Curtain measurements get confusing when “window width,” “rod length,” and “panel width” are used as though they mean the same thing. They don’t. Let’s work through what to measure, what to calculate, and what to put in your cart.

The most useful starting point: For two equal UniCurt pinch pleat or S-Fold panels covering a 100-inch usable span, start with 50 inches of finished width per panel — the fullness is already built into those headings. For the other four headings — grommet, rod pocket, tab top, and back tab — using 2× fullness across that same span, start with 100 inches of flat width per panel. The heading changes the calculation. Height, returns, and hardware compatibility still need their own checks.

1. Before measuring: identify your setup

Already have a rod or track? Keep it in place for the measurements. Note the usable curtain span, how the curtain attaches, and how far that attachment point is from the floor. A close-up of a ring or runner is useful alongside a photo of the whole window.

No hardware yet? Choose the proposed position and heading before committing to a finished curtain length. You can plan the coverage now, but the final height needs a known hanging arrangement. Where space is tight, installing or firmly confirming the hardware first removes one important uncertainty.

Replacing curtains that already fit? Their finished dimensions are a useful reference when the new curtains will use the same hanging arrangement. Label them “existing finished curtain measurements.” They are not raw window measurements and should not receive another allowance automatically.

Write every size as width × height, with units. One foot is 12 inches; one inch is 2.54 cm. A 14-foot rod is 168 inches—not 14 inches. For a fractional size, 34⅝ inches is 34.625 inches, not 34.58. Keep the actual readings rather than rounding several separate measurements along the way.

Measure each window separately, even when two openings look alike. Record the room, available wall on each side, clear space above the window, and any handle, sill, or other obstruction.

2. Measure coverage—not just the glass

The window width describes the opening or trim. The coverage width is the horizontal area the closed curtains need to cover. The total rod length may include decorative finials that curtains cannot travel over.

For an existing rod, identify the section the curtains can actually use. Do not include a decorative end simply because it is part of the rod. For a track, check the carrier travel and end stops. Side returns and special overlaps are separate details, explained below.

For a new installation, start with the window or trim width and add the intended left and right extensions:

Planned front coverage = window width + left extension + right extension

Our usual customer-service planning suggestion is around 6–10 inches beyond each side where there is room. It is a starting point, not a rule that every room must follow. An 80-inch window with 8 inches added on each side gives 96 inches of planned front coverage.

Check the actual wall space and the open curtain stack before finalizing those extensions. Where one side is close to a corner, matching a smaller extension on the opposite side may give a balanced arrangement, but it will not necessarily keep all the glass clear when the curtains open.

Ordering a decorative rod too? In our Zoe rod order discussions, the specified overall length includes the finials. A required curtain coverage of 100 inches is therefore not automatically an instruction to order a 100-inch tip-to-tip rod. Confirm the usable span and total assembled length for the selected hardware.

3. Calculate the width of each panel

This is the question we hear most often: “Your tool says two 28.5-inch panels for my 57-inch rod. Will that really be enough?” For a normal two-panel pinch pleat arrangement, yes: 28.5 inches is the finished pleated width of one panel, not the width of the cloth before pleating.

Heading What the ordered width means Two panels across a 100-inch usable span*
Double Pinch Pleat Finished pleated width; approximately 2× fabric fullness is already built in. 2 panels × 50 inches wide
Triple Pinch Pleat Finished pleated width; approximately 2.5× fabric fullness is already built in. 2 panels × 50 inches wide
S-Fold Intended finished coverage; approximately 2.6× fabric fullness is built in. Confirm the matching runner system. Start with 2 panels × 50 inches of coverage, subject to the heading/runner check.
Grommet, using 2× fullness Flat panel width. You allow the fabric that will gather into folds. 2 panels × 100 inches wide
Rod Pocket, using 2× fullness Flat panel width. You allow the fabric that will gather into folds. 2 panels × 100 inches wide
Tab Top, using 2× fullness Flat panel width. You allow the fabric that will gather into folds. 2 panels × 100 inches wide
Back Tab, using 2× fullness Flat panel width. You allow the fabric that will gather into folds. 2 panels × 100 inches wide

*Illustrative front-coverage calculations for two equal panels. Confirm any side returns, center overlap, and hardware-specific requirements separately.

For pinch pleat curtains

Finished width per equal panel = confirmed coverage width ÷ number of panels

A 57-inch span divided between two panels gives 28.5 inches each. A 100-inch span gives 50 inches each. You do not double those numbers again to pay for the pleats—the pleating fabric is already part of the construction.

For a flat-width heading

Flat width per equal panel = coverage width × chosen fullness ÷ number of panels

Using the 2× example, 100 × 2 ÷ 2 = 100 inches per panel for grommet, rod pocket, tab top, or back tab. Two 50-inch flat panels would provide only 100 inches of cloth in total, without the extra fabric that makes the open folds.

A one-panel arrangement does not use “divide by two.” Unequal panels do not use “divide equally.” Decide how many panels you need and where they will close before using a formula.

For decorative side panels that will stay in position, say that clearly. A decorative panel does not automatically have enough width to cover the window. Also remember that an evenly divided closed width does not guarantee a particular gathered appearance when open.

4. Measure the finished curtain length

Finished length means the distance from the top of the finished fabric to its bottom edge. Your ceiling-to-floor height, rod-to-floor height, and hook-to-floor height can all be different measurements. Name the starting point whenever you send a number.

Hanging arrangement What to measure and check
Pinch pleat on a rod with rings Show the ring’s hook attachment point and measure from there to the floor. Confirm where the top of the fabric will sit relative to that point.
Pinch pleat or S-Fold on a track Identify the actual carrier/hook attachment and the finished heading position. The bottom of the ceiling is not necessarily the top of the curtain.
Grommet The rod passes through the heading and fabric extends above it. Confirm that top offset for the actual eyelet/rod combination before converting a rod-to-floor reading.
Rod pocket or another heading Confirm how the rod sits within the heading and where the fabric begins; do not copy a ring-hung curtain’s allowance.

Once the top of the finished fabric has been established, the calculation is simple:

Finished length = distance from the finished fabric top to the floor − desired floor clearance

Example only: If that confirmed fabric-top position is 90 inches above the floor, and you choose a ½-inch gap, order a finished length of 89.5 inches. The ½ inch is a preference in this example, not a universal factory deduction.

A measurement taken at a hook still needs the hook-to-fabric-top relationship. When the fabric top sits above the measured hanging point, that height difference is added before subtracting the floor gap; when it sits below, the difference is subtracted. We can help confirm that relationship from the actual heading and hardware.

Describe the finish you prefer: just off the floor, touching the floor, or deliberately resting on it. “Floor length” alone leaves room for misunderstanding. For a wide installation, measure at several positions and send all readings when they differ.

Do not automatically add or subtract one or two inches. That can work for a particular verified setup and be wrong for another. A 96-inch ceiling height does not, by itself, establish a 95-inch curtain order.

For café curtains or another shorter treatment, choose the intended bottom position and use the same fabric-top-to-finished-bottom logic. Do not calculate a floor-length curtain first and assume the same adjustments apply.

5. Allow for side returns and center overlap

A side return is the section that turns from the curtain’s front toward the wall. A center overlap lets the two leading edges cross when the curtains close. Fullness is the cloth folded into pleats. These are three separate things.

For an ordinary pair, dividing the confirmed coverage width by two is the starting point. But a traverse rod with overlapping master carriers, or a specified return around each end, needs more information. The pleating fabric does not automatically become extra usable width.

Send a photo of the master carriers and rod ends. State the required return measurement and where it begins. For example, “4-inch return from the last pleat to the outer fabric edge” is much clearer than “add a little extra.” Explain how that section will attach to the wall and which panels are left- or right-handed.

Before paying, make sure the final summary says whether returns and overlap are already included in the ordered panel width or recorded as additional construction details. Do not add them a second time—and do not assume they are included just because the curtain has built-in fullness.

6. Estimate the space curtains occupy when open

The gathered curtain at each side is called stack-back. It matters when you want to preserve daylight or have only a few inches of wall beside the glass.

For some pinch pleat orders, our initial planning estimate is approximately one-sixth to one-fifth of each panel’s finished width. A 60-inch panel might therefore need around 10–12 inches to gather. Two panels create two separate stacks—not one shared 10–12-inch bundle.

If the accessible rod extension on that side is only 4 inches, roughly 6–8 inches of that example stack may remain in front of the glass. This is a planning calculation, not a guaranteed installed result.

Fabric thickness, lining, pleat construction, rings or carriers, end stops, and gathering all change the result. A track and a rod with rings should not automatically be given identical stack-back figures.

A tieback can gather the body neatly, but it does not remove the width occupied by the heading and hardware. Tell us the chosen fabric and lining before relying on an estimate. Ordering a narrower curtain just to reduce the stack may leave you short of coverage when it closes.

7. Plan two windows and four panels on one rod

One long rod can visually connect neighboring windows. First draw the whole wall and mark where every panel should sit both open and closed.

Consider this illustrative layout: an 85-inch window, a 39-inch middle wall, a 33-inch window, and 12-inch extensions at the far left and right.

12 + 85 + 39 + 33 + 12 = 181 inches of planned front coverage

For two pairs, dividing the middle wall equally gives 19.5 inches to each window group:

Group Coverage calculation Two equal pinch pleat panels
Left, larger window 12 + 85 + 19.5 = 116.5 inches 58.25 inches each
Right, smaller window 19.5 + 33 + 12 = 64.5 inches 32.25 inches each
Total 181 inches 4 panels

Those are front-coverage figures before any separately agreed returns or overlaps. Giving each group 20 inches of a 39-inch middle wall counts an extra inch. Any intended overlap should be named rather than hidden by rounding.

Also, 181 inches of coverage is not automatically a 181-inch decorative rod including finials. Check the hardware’s usable span and total assembled size.

A standard center-opening traverse arrangement is not automatically configured to operate two independent pairs. Confirm the carriers, stops, supports, and movement for all four panels. Closed widths alone do not guarantee that the middle stacks will meet exactly like an inspiration photo.

8. Check corners, crown molding, and bay windows

Near a wall or crown molding, measure the available space for the whole assembly: brackets, screw positions, rod, rings, finials, and curtain heading. A bracket base fitting inside a gap does not by itself confirm enough assembly room or a suitable fixing point.

For example, a 2.18-inch base may fit visually within a 2.5-inch gap, but the screw positions and actual mounting surface still need checking. An installation video cannot establish what is behind the wall or ceiling.

For a bay or angled window, do not use a straight-wall width as the complete ordering instruction. A bay needs its own measurement review; the straight-wall examples above are not a bay-window ordering formula. Provide a sketch of each section and the actual hardware path so the layout can be reviewed individually.

With wide, lined panels, confirm support locations and the proposed curtain weight as part of the hardware choice. Neither a larger number of brackets nor a rod diameter alone guarantees that the entire installation is suitable.

9. Check S-Fold runners and grommet sizes

Keeping an existing track for S-Fold

Our cord-spaced S-Fold arrangement needs the curtain heading and runner spacing to match. Independent gliders with no spacing cord are not automatically suitable for that system.

Send the exact track model or product link, a close-up of the runners, the fully extended spacing where there is a connecting cord, and photos of the rail ends. To review replacement runners, we also need the bottom slot opening, internal channel width and height, and retaining-edge shape or thickness.

One measurement—such as a ⅛-inch slot—does not confirm the entire fit. A runner must move through the required route, including joints, and work with the end stops and curtain attachment.

Do not calculate a new panel’s width from hook count alone. Five attachment points have four intervals between the first and last, plus the relevant edge treatment. In some arrangements an odd count also changes the edge-fold direction. Agree the actual heading and runner layout before ordering.

Keeping a rod for grommet curtains

Confirm the eyelet’s inner diameter, not just its outer size, and check the required operating clearance around the rod. The fabric above the eyelet matters for length. Ring sizes from another retailer are not a substitute for the fittings used in your order.

When an existing system cannot be matched confidently, discuss a suitable pinch pleat arrangement or matching S-Fold hardware rather than assuming the fabric alone will solve the mismatch.

10. Measure lined curtains and separate sheer layers

A lining is another layer within the curtain; it is not a reason to double the selected finished pinch pleat width again. It can, however, change the weight and open stack, so include the lining in the configuration you ask us to check.

Separate sheers and drapes are different layers. Decide whether both need to open and close independently, then confirm the hardware and measurements for each. Do not divide the window’s width in half between them when both layers are expected to cover the full opening.

For blackout-lined curtains, check the middle, sides, top, and bottom as well as the lining. Light-blocking fabric does not close an uncovered gap. Returns, overlap, and floor finish should be deliberate choices, not extra fabric added at random.

When an option is not shown on the page, ask us to confirm the exact construction and any additional cost before using another selection as a placeholder.

11. Measuring Roman or bamboo shades instead?

Do not use the curtain fullness formulas for a shade. A Roman or bamboo shade needs its own finished width, drop, mounting type, and mechanism check.

Inside mount: Record the opening width at different positions, the height, and available mounting depth. Keep the raw readings. Confirm whether you or production applies the fitting deduction; never subtract it twice. Confirm the deduction and minimum depth for the selected shade model rather than treating either as a universal measurement.

Outside mount: Measure the area you want the shade to cover, including trim where appropriate, and mark the intended top and bottom. Glass-only dimensions are not enough when the shade must also cover the frame.

Copying existing blinds: A finished blind that fits well can be a useful reference. Say that you measured the blind itself, not the opening, and explain the mounting arrangement. A different headrail may need a different fit review.

Several shades together: State the quantity and each size. “Two shades, each 38 × 51 inches” is not the same order as “one shade across an 80-inch framed opening.”

Handles, sills, and cranks: Provide side-view measurements and check the fabric both raised and lowered. Headrail depth alone does not describe the full folded shade. For a very wide shade, confirm the complete size, fabric, lining, and lift system; do not bypass a website size restriction without an approved configuration.

12. Turn the measurements into an order

Once the measurements are agreed, the cart should read like a clear instruction to the workroom. Check the product and color, heading, width of one panel, finished height, lining, quantity, and any written special requirements.

Here is a hypothetical simple order: a confirmed 100-inch front span, two equal double pinch pleat panels, a finished fabric-top position 90 inches above the floor, and a chosen ½-inch clearance.

Order field Example entry
Fabric and color Your selected fabric and confirmed color
Heading Double Pinch Pleat
Width 50 inches per panel
Height 89.5 inches, based on the confirmed fabric-top position
Quantity 2 panels
Lining The agreed option; not an assumed upgrade
Returns / overlap No special requirement in this example; record yours separately when needed

Open the product directly on our website and make sure the size fields and heading options appear. Some customers have reported missing customization options through shopping apps; do not assume an order with missing details will be made correctly.

After adding the item to the cart, compare it with your notes. Check that the height has not changed, the width belongs to one panel, and the quantity is correct. If you entered 84 inches and the cart shows 60, do not approve the incorrect measurement. Capture both screens and contact us.

For a manual quotation or special add-on, review the written product specification as well as the payment amount. A custom payment link is not a substitute for the sizes and options. Already paid with an incorrect measurement? Send the order number and intended dimensions promptly and ask for written confirmation of the production change.

13. Quick answers to common questions

Do I double the width for pinch pleat curtains?

No. UniCurt pinch pleat widths already include the fabric needed for the sewn pleats. Divide the confirmed coverage between your panels, then confirm any special returns or overlaps.

Is the listed width for one curtain or the pair?

In the ordering method described here, it is the width of one panel. Set the quantity separately.

Can I measure from the ceiling and subtract one inch?

Only when that calculation matches the actual heading and hanging position. Otherwise, confirm the finished fabric top first.

Should I buy the rod first?

An installed or precisely confirmed hanging position makes final height easier to establish, especially under crown molding. Planning both together is possible, but do not finalize a custom length while the attachment position is unknown.

Does extra fullness automatically cover side gaps?

No. Pleating fullness, side returns, and center overlap are different specifications. Blackout lining does not replace the missing coverage either.

Can a room preview give me the dimensions?

A preview helps you compare the look. It is not a measured drawing. Send actual readings before the order is made.

14. Copy-and-fill measurement worksheet

Not sure which number belongs where? Send the information below. We can work from the raw measurements instead of trying to undo an allowance you guessed.

Room / window label:
Curtain or Roman/bamboo shade:
Measurement units: inches / cm
Existing hardware or planned hardware:
Hardware model / product link:
Window or outer-trim width:
Left clear wall / right clear wall:
Space above window:
Usable rod or track span:
Total rod length including finials, if applicable:
Distance to floor (state the exact starting point):
Additional floor readings across the span:
Preferred bottom finish or floor gap:
Number of panels and intended opening directions:
Heading style:
Fabric / color:
Lining:
Side return / center overlap requirements:
For S-Fold: runner type, spacing, count and end points:
For shades: inside/outside mount, depth, quantity and obstacles:
Photos: whole window, hardware close-up, side view where needed
Final width × height PER PANEL (once confirmed):

Our online measurement tool can help you get started. For an unusual layout, send the results with a photo and keep the distinction between room measurements and finished product sizes.

The goal is not to add more fabric “just in case.” It is to order the right finished coverage and length for the way your curtains will actually hang.